Two-component epoxy system with low density, filled with non-abrasive fillers. Can be kneaded, shaped and modelled. Very easy to work with after curing. Cures at room temperature. Component A.
Please remember to order the epoxy resin PE 640 A (component A) separately!
The epoxy putty can be shaped and modelled and is suitable for restoring sculptures and for building small to large models, moulds and support moulds. Very light material due to its low density. Very easy to work with tools after at least 12 hours of curing, as the inert fillers do not contain any abrasive components.
PROCESSING:
Check the initial masses of resin and hardener and homogenise them if necessary before use. Weigh the two components carefully (resin and hardener) and mix them in the exact mixing ratio until a homogeneous mass is obtained. If possible, avoid creating air bubbles. Then process the compound immediately. A wax-based product is suitable as a release agent to prepare the surface of an object to be moulded (see manufacturer's instructions).
TECHNICAL INFORMATION:
Mixing ratio by weight (g): 100:100 (A:B)
Working time at 25°C (500 ml): 20 - 25 minutes
Working time with mixer at 25°C (4 kg): 15 - 20 minutes
Setting time at 25°C (15 ml, 5 mm): 2 - 3 hours
Exothermic peak at 25° C (500 ml): 70° - 80° C
Demoulding time (15 ml, 5 mm, 25° C): 15 - 20 hours
Post-curing at 60° C (optional): 10 - 15 hours
Maximum recommended casting thickness: 30 - 40 mm
The maximum casting thickness depends heavily on the mould material, the dimensions and the room temperature.
Properties of resin PE 640 NA/A (component A) before processing:
Colour: white or brown
Density at 25° C: 0.60 g/ml
Properties of hardener PE 640 B (component B) before processing:
Colour: beige
Density at 25° C: 0.95 - 1.00 g/ml
Properties after curing:
Colour: straw yellow or brown
Density at 25° C: 0.52 - 0.57 g/ml
Hardness at 25° C: 70 - 75 Shore D/15
Glass transition: 75° - 85° C
Recommended maximum operating temperature: 70° C
Hardener PE 640 B (component B)
The product is subject to labelling according to GHS/CLP directives. Labelling according to Regulation (EC) 1272/2008:
UFI:
GHS05, GHS07
Signal word: DANGER
Contains: Fatty acids, C18unsatd., dimers, oligomers. Reaction products with tallow fatty acids
Hydrocarbons, polymers with phenol
2,4,6-Tris(dimethylaminomethyl)phenol
Benzyl alcohol
3-aminomethyl-3,5,5-trimethylcyclohexylamine: May produce an allergic reaction.
H302 Harmful if swallowed. H314 Causes severe skin burns and eye damage. H317 May cause an allergic skin reaction. H412 Harmful to aquatic life with long lasting effects
P261 Avoid breathing dust/ fume/ gas/ vapour/ spray. P264 Wash tools thoroughly after handling. P273 Avoid release to the environment. P280 Wear protective gloves/ clothing and safety goggles/ face shield.P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P310 Immediately call a POISON CENTER or doctor.
Special provisions according to Annex XVII of REACH and subsequent amendments: None.
No customer reviews for the moment.
check_circle
check_circle
